订购热线13722252255

联系我们

手机:13722252255
电话:13722252255
微信:13722252255
地址:保定市唐县长古城工业区

新闻资讯

当前位置:首页-新闻资讯

铜鼎厂家制作大型铜鼎的流程

发布时间:2022-06-13点击量:48

铜鼎的历史悠久,铸造工艺也相对别的青铜器来说比较先进,它是古老青铜器的代表,也是中国国代铸造工艺的一个代表作,时至今日,我们的铜鼎依然存在在我们的生活中,古时候是权力地位的象征,现在是镇宅除煞旺财的宝物,更是人与人交流的高雅工艺品,接下来带你讲述铜鼎的铸造工艺流程。

The bronze tripod has a long history, and its casting technology is more advanced than other bronze wares. It is the representative of ancient bronze wares, and also a representative of the casting technology of China's national dynasties. Today, our bronze tripod still exists in our lives. In ancient times, it was a symbol of power and status. Now it is not only a treasure to eliminate evil and prosperous wealth, but also an elegant handicraft for people to communicate. Next, I will tell you about the casting process of the bronze tripod.


IMG_20210402_091350_副本_副本.jpg


(1) 铜鼎母模制作:制作好的青铜器,必须有完美的母模,这是青铜器制作*关键的步骤。如果是复制,就需要用青铜器专业去锈法把古器物清理干净再翻制模具;如果是仿制,就需要雕刻出一件与原古器物一样的母范。

(1) Bronze tripod mother mold making: a good bronze ware must have a perfect mother mold, which is the key step in bronze ware making. In case of reproduction, it is necessary to use the bronze professional derusting method to clean up the ancient objects and then turn over the mold; If it is an imitation, it is necessary to carve a female model that is the same as the original antique.


鼎盛千秋尺寸.jpg


(2) 铜鼎翻制模具:过去用石膏翻制模具,由于石膏凝固以后,质脆、疏松,所以做出模具的纹饰,立体感不强、线条不够流畅、利用率不高,往往修整后,纹饰变形、失去原古物的韵味。现在模具翻制,一般采用温室硫化硅橡胶,不仅方法简单,而且制作的模具效果非常好。

(2) Bronze tripod mold making: in the past, gypsum was used to make molds. Because the quality of the gypsum was brittle and loose after solidification, the mold decoration was made. The three-dimensional sense was not strong, the lines were not smooth enough, and the utilization rate was not high. After finishing, the decoration was often deformed and lost the charm of the original antiquities. At present, the mold is usually made of greenhouse vulcanized silicone rubber, which is not only simple, but also has a very good mold effect.


IMG_20210331_114155_副本_副本.jpg


(3) 铜鼎模壳制作及铸造打磨:现在一般都采用失蜡铸造,这种方法简单快捷,而且能够不失原器形的韵味,可铸造出来工艺特别复杂的青铜器。

(3) Manufacturing, casting and polishing of bronze tripod shell: now, wax loss casting is generally used. This method is simple and fast, and can not lose the charm of the original shape. It can cast bronze vessels with particularly complex processes.


8.方形圆形铜鼎铸造价格.jpg


 铜鼎铜胎做旧(黑漆古皮壳、红斑、绿锈做旧法):只有完美的铜胎而没有漂亮的外衣,还不能算一件精美的复制品。过去的做旧方法,已不能满足人们的鉴赏要求,现在做旧采用了电解作皮、化学作锈、新处理粘锈的综合方法。

 The old copper body of the bronze tripod (the old black lacquer shell, red spots and green rust method): only the perfect copper body without a beautiful coat can not be regarded as a beautiful replica. In the past, the old methods can no longer meet the requirements of people's appreciation. Now, the comprehensive methods of electrolytic skin, chemical rust and new treatment of stick rust are adopted.

联系我们

手机:13722252255
微信:13722252255
地址:保定市唐县长古城工业区
地址:保定市唐县长古城工业区 手机:13722252255 电话:13722252255 
版权所有:河北青铜鼎工艺品制作生产厂家 
ICP备案编号:冀ICP备19005158号-2
网站首页 |关于我们 |产品展示 |新闻资讯 |工程案例 |雕塑知识 |资质荣誉 |营销网络 |联系我们
备案图标.png

冀公网安备13062702000173号